Board Thickness and Wear Layers in Wide Plank Flooring
Board thickness is the full depth of each plank, and on an engineered board the wear layer is the top layer of real hardwood that you see, touch and live on. Our wide plank floors range from 5/8 inch to 1 inch thick depending on species and construction, and our engineered Northern White Oak and Southern Pecan carry a sawn wear layer of 4.5 to 8 mm.
These numbers are easy to skim past on a spec sheet, but they shape the drawings more than most people expect. Thickness decides how floors meet stairs, doorways and other rooms, and the wear layer decides how much real wood sits at the surface of an engineered floor.
Thickness Options by Species
Each of our three species is made in its own set of thicknesses, so the choice starts with the wood you have fallen for. Every board is sawn, dried and milled, then finished by hand, at our Bryan, Texas facility, where we have been making wide plank floors since 1998 for custom homes across the United States. Keeping the whole process in one place means the same team oversees each board from rough lumber to finished plank.
Northern White Oak
Our Northern White Oak wide plank flooring is made in three thicknesses: 1 inch, 13/16 inch and 3/4 inch. It is offered in both solid and engineered construction. With three thicknesses to choose from, it gives architects the most room to fine-tune finished heights across a large home.
French Oak
French Oak is made in 1 inch and 7/8 inch thicknesses, in solid and engineered construction. Our French Oak comes from France, milled from the lumber of French forest trees 150 years old and older, and it is sold in single widths of 10 and 12 inches.
Southern Pecan
Southern Pecan is made as a 3/4 inch solid board or a 5/8 inch engineered board. The engineered option is the thinnest board we make, which can be useful where finished heights are tight. Pecan's strong color variation, from cream sapwood to darker heartwood, reads the same in either construction because the face is real Pecan either way.
A note on Natural Face
Our signature Natural Face texture is intentionally crafted with overwood and slight board height variance, which is part of what makes it read like a century-old floor. When the architect is checking finished heights, it helps to know that this gentle variation is designed into the surface. Note it in the specification so the trades on site expect it and leave it as intended.
What a Sawn Wear Layer Is
An engineered board is built in layers, with a stable core below and a layer of the chosen hardwood on top. That top layer is the wear layer, and it is the only part of the board anyone sees once the floor is down. How it is cut, and how thick it is, matters more than any other detail of the construction.
Why sawn matters
A sawn wear layer is cut from the lumber with a saw, the same way a solid board is, so its face shows the same grain you would see on solid wood. Wood can also be sliced or peeled into thinner sheets, which changes how the grain looks and leaves less wood at the surface. We saw our own wear layers at our facility, alongside the lumber, so the face of an engineered board comes from the same stock and the same hands as our solid floors.
What 4.5 to 8 mm means in practice
For reference, 4.5 mm is a little under 3/16 inch and 8 mm is just over 5/16 inch. That is a meaningful layer of real hardwood sitting on top of the core, with enough depth to carry the character of a live sawn face. A thicker wear layer simply leaves more wood above the core over the life of the floor, which is worth weighing on the main living areas of a home.
Live sawn grain on the face
Because every floor we make is live sawn, an engineered board shows the same natural mix of rift, quarter and plain sawn grain. In Northern White Oak, that means a grain that is not intrusive and warm, earthy browns from light to dark. From the surface, the grain reads just as it would on a solid board.
How the finish relates to the wear layer
On an engineered board, the finish sits on or in the wear layer, never in the core. Our water-based urethane forms a low VOC protective coat on the surface, while our plant-based penetrating oil soaks into the pores of the wood and develops an aged patina over time. Either way, it is the wood in the wear layer that gives the floor its color and character, which is why that layer deserves attention in the specification.
Where to read about solid and engineered
This article covers thickness and the wear layer only, not the full choice between platforms. If you are still deciding which construction suits each part of the house, our guide to engineered vs solid wood floors walks through that decision in detail.
How Thickness Affects Stairs and Transitions
Thickness becomes most visible where the floor stops. Stairs, doorways and the edges of rooms are where a fraction of an inch either looks deliberate or looks like a fix, so these details are worth drawing early.
Stair treads and landings
Every stair tread we make is a single solid board, and nosing is only made for the landings, where the stair meets the floor. That landing nosing is profiled around the floor's thickness, so it is worth settling thickness before the stair is detailed. Treads are matched to the floor by species, color and finish, so the stair reads as part of the floor rather than an add-on.
Doorways and thresholds
Floor thickness sets the finished floor height, which in turn sets door undercuts and threshold details. On a large home with many interior doors, settling thickness early saves a long list of adjustments later. It also helps the architect decide where a threshold is wanted as a design detail and where the floor should simply run through.
Meeting other floor finishes
Where wood meets a different floor finish in an entry or a bathroom, the two surfaces need to finish at the height the design intends. Knowing the exact thickness of the wood lets the architect and builder plan the build-up under each material, so the transition is a clean line rather than a ramp or a step nobody planned.
Thickness and Installation
Matching the board to the subfloor
Our hardwood flooring install guide follows NWFA guidelines and covers both nail-down installation over plywood and glue-down installation directly on concrete. The board you choose should suit the subfloor it is going over, so share the thickness and construction with your installer while the subfloor is still being planned. For nail-down floors the guide calls for 1/2 inch of expansion space at the perimeter, which your trim details should allow for.
Frequently Asked Questions
Is a thicker floor always the better choice?
Not necessarily. The right thickness is the one that suits the subfloor and the finished heights in the plans. A 1 inch board has real presence underfoot, but a 13/16 inch or 3/4 inch board in the same species may be the better fit for a particular part of the house.
Can solid and engineered boards be used in the same home?
Yes, as long as the heights are planned. In Southern Pecan, for example, the 3/4 inch solid board and the 5/8 inch engineered board differ by 1/8 inch, which needs to be accounted for wherever the two meet. Drawing that transition at the design stage keeps it from becoming a site problem.
How can we see the construction before ordering?
Once we have talked through your project and narrowed down the species, texture and color, we make a built-up sample measuring 16 by 19 inches, along with color samples. Every sample is handcrafted and hand-finished, so you are looking at the same kind of board, texture and finish your floor will have.
Settle the Construction Before You Specify It
Thickness and wear layer are easiest to settle in conversation, with the plans in front of you. Get in touch with our team about your project, and we will help you match the construction to the plans for your home, with a handmade sample to follow once the details are clear.



